GMC Truck Forum banner

101 - 120 of 133 Posts

·
layin big rubber
Joined
·
1,457 Posts
Discussion Starter #101
only update on the truck is im almost done installing the s10 blazer fuel tank
 

·
layin big rubber
Joined
·
1,457 Posts
Discussion Starter #102
  • Like
Reactions: 07Burb

·
layin big rubber
Joined
·
1,457 Posts
Discussion Starter #103
  • Like
Reactions: 07Burb

·
layin big rubber
Joined
·
1,457 Posts
Discussion Starter #104
92626571_1058302117878107_216563061497004032_n by joa kwin, on Flickr

s10 blazer gas tank is done and the lines extended for it and the wiring is good

I got the exhaust mounted


I don't like the placement of the battery and the air tank, I think im going to mount the battery where the air tank is right now
im not sure where im going to put the air tanks right now or the valve bank
 
  • Like
Reactions: 07Burb

·
layin big rubber
Joined
·
1,457 Posts
Discussion Starter #105

got the new starter put on and starting to clean around the truck so I can pull it out to clean the work area
 

·
layin big rubber
Joined
·
1,457 Posts
Discussion Starter #106

·
layin big rubber
Joined
·
1,457 Posts
Discussion Starter #107


starting to mess with the fitting of the fenders

im going to drop the front of the truck a few more inches
 

·
layin big rubber
Joined
·
1,457 Posts
Discussion Starter #108


turned the lca into flat plate arms
 

·
layin big rubber
Joined
·
1,457 Posts
Discussion Starter #109
  • Like
Reactions: 07Burb

·
layin big rubber
Joined
·
1,457 Posts
Discussion Starter #110
  • Like
Reactions: 07Burb

·
layin big rubber
Joined
·
1,457 Posts
Discussion Starter #111
  • Like
Reactions: 07Burb

·
layin big rubber
Joined
·
1,457 Posts
Discussion Starter #112


down



up

I got the fender mounted and running board and running board mounts
 
  • Like
Reactions: 07Burb and Heckwine

·
layin big rubber
Joined
·
1,457 Posts
Discussion Starter #113


I sectioned 4 inches out of the running board to center up the fender to the wheel

 
  • Like
Reactions: 07Burb

·
layin big rubber
Joined
·
1,457 Posts
Discussion Starter #114
im in the process of extending the A arms 3 inches per side so that the wheels can fill the fenders better
 

·
layin big rubber
Joined
·
1,457 Posts
Discussion Starter #115


the right lca



the fender to wheel gap is a lot better now
 

·
layin big rubber
Joined
·
1,457 Posts
Discussion Starter #116
 

·
layin big rubber
Joined
·
1,457 Posts
Discussion Starter #117


im starting to mock up the Nissan eps unit, im going to weld on a chevy spline to the end of it
 

·
layin big rubber
Joined
·
1,457 Posts
Discussion Starter #119



air tanks are mounted, ordered up the air fittings I need

going to mount the valve bank today or tomorrow

I need to ext the hose off the edc so it can connect to the air tanks
 
  • Like
Reactions: 07Burb

·
layin big rubber
Joined
·
1,457 Posts
Discussion Starter #120 (Edited)


im going to use this gen 1 s10 pedal box
and a booster and master and prop valve from a 2003 s10 blazer



valve mount set up





I plan to run some air line for the exhaust ports out the sides, two exhaust ports, one on each side of the truck, for a little puff of air, lol
 
  • Like
Reactions: 07Burb
101 - 120 of 133 Posts
Top