[phillipsjt27]

Where is the best place to buy fittings? I cant seem to find a single place that sells every thing I need in one place. Can some one point me in the right direction and maybe help with a list of what I need I have a plan but it seems hard to find everything.

 

[bigoakes50]

Local Parker store, AVS, Grainger just to name a few.

 

[Adjusted01]

www.airridefittings.com

it was good for me

 

[Cook]

I used a local truck shop. Look around your area. Places that sell parts for MAC trucks usually carry a lot of air fittings.

 

[squash]

http://www.mcmaster.com/#push-to-connect-tube-fittings/=cae3u2

 

[on1wheel06]

i have pretty much everything for a 3/8 valve 1/2" line setup.

 

[Zach.]

I got mine at innovativeairsuspension.com

 

[phillipsjt27]

I cant seem to find female brass tee's with a 1/8 guage fittings anywhere. I have to buy online because im in Germany and need the parts in the states.

 

[Cook]

do you need valves? im selling 8 of them and i have a bunch of fittings i can throw in too

 

[Zach.]

I cant seem to find female brass tee's with a 1/8 guage fittings anywhere. I have to buy online because im in Germany and need the parts in the states.

What size brass tee do you need?

 

[on1wheel06]

I cant seem to find female brass tee's with a 1/8 guage fittings anywhere. I have to buy online because im in Germany and need the parts in the states.

you want street Ts with 1/4" mnpt / 1/8 line... i haz!

 

[phillipsjt27]

do you need valves? im selling 8 of them and i have a bunch of fittings i can throw in too

I already have valves, thanks...

What size brass tee do you need?

3/8 with 1/8 gauge fitting

This is how I plan on setting up my valves...

Let me know wht you think..

 

[Zach.]

What size are your tank ports? Man I'm glad I bought my fittings when I did. Those damn Tee's are expensive now.

 

[phillipsjt27]

I have two tanks, each with 4 1/2" ports on the side, 1 1/2" Port on each end and 1 1/4" drain on the bottom. My plan is.....

4- one 1/2" port per set of valves
1- 1/2" port for edc
1- 1/2" port for Electric backup
1- 1/2" port for pressure switch
2- 1/2" ports connect two tanks together
2- 1/4" port for drain per tank
1- 1/2" port for shredder valve
2- 1/2" ports plugged

 

[Zach.]

Do you for sure want your valves setup like that? From the pictures it looks like it blocks some ports. Also if you don't find any 3/8" Tee's with a 1/8" gauge port then you could use a 3/8" cross and put a reducer on one end with a 1/8" gauge fitting. Will you be using the square D pressure switch with a unloader port?

 

[phillipsjt27]

Yes I have a Square d can you school me on the plumbing for it, as well as fill me in on better ways to route my valves.

 

[Zach.]

I believe I showed you pictures before of how my tanks will be setup. I'm using the Slim 5 Gallons. I think the same ones that you have. I'll throw it all together afterwhile and post a picture.

 

[Marcos]

Do you for sure want your valves setup like that? From the pictures it looks like it blocks some ports. Also if you don't find any 3/8" Tee's with a 1/8" gauge port then you could use a 3/8" cross and put a reducer on one end with a 1/8" gauge fitting. Will you be using the square D pressure switch with a unloader port?

Thats what I did, they didn't offer those all in one tees when I bagged my truck, or I didn't look hard enough.

 

[heath bagged]

I buy everything from gaugemagazine.com great people to deal with.

 

[Marcos]

I buy everything from gaugemagazine.com great people to deal with.

If you buy from there, use coupon code frmember... 5% off.