[shibbby911]

can i go lower in the front with out messing up my fenders or something? the wheels and tires i have are kmc slides with a 275/30/24 im already dropped 4 in the front but id like to drop it another inch

 

[shibbby911]

bump?

 

[OHNINE]

offset?
i know unleashed is 6/9 on same tire size.
dont think he modded the liners?

 

[shibbby911]

its a +25 offset 9.5" rim

 

[OHNINE]

ehhhhh. if u have another +10 offset... maybe around 35 i would say yea. go lower. but with 25. maybe to close for comfort.

 

[shibbby911]

man i wish i knew for sure what off set does unleashed have do u know and his rim width?

 

[OHNINE]

i know they are decenti wheels let me look those up

 

[OHNINE]

24*10 30 offset dcenti dw19B

so u are within 5mms of him... imo if he dont rub u shouldnt. not that big of a difference

 

[shibbby911]

k cool how are most people doin 5 in the front i have springs and spindles now

 

[OHNINE]

i think to go lower without camber would be 4" arms and coil relocator set to 1 or 2"..

u can add coil relocators but IIRC u will have bad camber. i dont know though.

 

[shibbby911]

oh ok cool im guna go by a local shop 2maro so ill find out for sure then

 

[drinkmetrx2135]

im at 4/7 with 295/35/24 with +25 offset. on hard turns either way i rubbed. ive had to relocate(pull back) and zip tie the cable that is behind the liner and pull the liner backand now minimal rub on hard turns. im looking to go to 5 in the front also but then id have to do some cutting. i dont know how that helps but im worried about the same thing. oh and my rims are 24x10

 

[OHNINE]

ur tires r to big to go lower. had same tires on my 24 and i had 30 offset. no way i could go lower without smaller tires imo

 

[Tukn4s]

24*10 30 offset dcenti dw19B

so u are within 5mms of him... imo if he dont rub u shouldnt. not that big of a difference

+25 offset on 9.5" rims give you the same front spacing as +30 offset on 10" rims. you'll have to cut and clear space to go down more.

To answer the question:
A truck can always go lower, you just have to have the balls to get it there.

 

[drinkmetrx2135]

To answer the question:
A truck can always go lower, you just have to have the balls to get it there.

I love that way of thinking. I need to figure out what I need to do to make it work.

 

[SuspensionSource]

Don't use lowering control arms. Just the Spindles,Coils and/or Belltechs Lowering Strut.

 

[OHNINE]

+25 offset on 9.5" rims give you the same front spacing as +30 offset on 10" rims. you'll have to cut and clear space to go down more.

To answer the question:
A truck can always go lower, you just have to have the balls to get it there.

with the right tire... yea it can go down.

 

[lowC10]

My buddy has those size tires on a 6" drop up front, just pull the plastic liners out and you should be fine.

 

[NORCAL SS]

djm 4 inch a arms and belltech drop struts for 5 inches no probs on ones i do.

for guys that want to slam it djm 4 inch a arms with belltech 2 inch spindles.

Hit me up if you have quetsinos.

 

[NORCAL SS]

i just read the offset again duhh cancel that.

usually on the 6/9s on customers trucks i do i run a 24x9.5 with at least 35mm offset and 275 25 24