GMC Truck Forum banner

1 - 4 of 4 Posts

·
Registered
Joined
·
397 Posts
Discussion Starter #3
Fine then.....I found it my damn-self :read:

Found it on another GMTruck site :nono:

Transmitter Programming '03 silverado

Important
Do not operate or program the transmitters in the vicinity of other vehicles that are in the keyless entry program mode. This prevents the programming of the transmitters to the incorrect vehicle.


There are 3 methods for programming transmitters which are listed below as method 1-3. Up to four transmitters may be programmed to the passenger door module (PDM). Each programmed transmitter is given a position of #1-#4 in the PDM memory.

Method 1 - No Tools Required, Program All Transmitters

Important
All transmitters which are to be recognized by the PDM must be programmed in a single programming sequence. When using this program method, all previously programmed transmitters will be erased upon the receipt of the programming signal from the first transmitter.

The order in which the transmitters are programmed will determine its numbering position within the PDM memory. The first transmitter programmed will be transmitter #1, and the second transmitter programmed will be transmitter #2. The number stamped on the transmitter case is for reference only: #2 can be programmed as #1, or vice versa. Additional unnumbered transmitters are also available.


Close all the vehicle doors.
Insert the ignition key into the ignition lock cylinder.
Press and hold the door unlock switch.
While holding the door lock switch in the unlock position, cycle the ignition ON, OFF, ON, OFF.
Release the door unlock switch. The doors will lock and unlock to confirm the program mode.
Press and hold the LOCK button and the UNLOCK button simultaneously on one transmitter. After a delay of approximately 15 seconds, the doors will lock and unlock to confirm the programming of that transmitter.
Repeat the previous step to program up to four transmitters.
Turn the ignition switch to the RUN position in order to exit the keyless entry transmitter programming mode.
Operate the transmitter functions in order to verify correct system operation.

xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
xxxxxxxxx

Driver Personalization
Memory Seat Programming
Perform the following actions in order to program the memory seats for 2 separate drivers. Both outside mirrors and the radio station presets can also be programmed with the seat position:

Move the seat to the desired position. Include the recliner, lumbar, and side wing area seat position.
Press the correct memory seat button for the specific driver and hold for 3 seconds. After pressing the switch a double chime should be heard.
Repeat the steps for the second driver.
Easy Exit Seat Programming
Perform the following actions in order to program the memory seats for 2 separate drivers:

Press the correct memory seat button for the specific driver. The seat will move to the last stored memory position.
Move the seat to the desired exit/entry position.
Press the exit button and hold for 3 seconds. After pressing the switch a double chime should be heard.
Repeat the steps for the second driver.
Programming Features with the Driver Information Center
To enter programming with the DIC, perform the following actions:

Turn ON the ignition with the engine OFF.
Ensure that the vehicle is in PARK or that the park brake is applied.
Press the personalization button on the DIC to scroll through all of the personalization options.
Automatic Locking/Automatic Unlocking
Continue with the following steps in order to program the automatic door locks feature:

The DIC displays LOCK DOORS: OUT OF PARK, MANUALLY or WITH SPEED.
Press the select button in order to scroll through the above choices.
Press the personalization button in order to select the displayed choice and to advance to the next option.
The DIC displays UNLOCK: ALL IN PARK, ALL AT KEY OUT, DOORS MANUALLY or DRIVER IN PARK.
Press the select button in order to scroll through the above choices.
Press the personalization button in order to advance to the next option.
Remote Activation Verification
Continue with the following steps in order to program the remote activation verification feature:

The DIC displays REMOTE LOCK FEEDBACK: HORN, LAMPS, BOTH, or OFF.
Press the select button in order to scroll through the above choices.
Press the personalization button in order to select the displayed choice and to advance to the next option.
The DIC displays REMOTE UNLOCK FEEDBACK: HORN, LAMPS, BOTH, or OFF.
Press the select button in order to scroll through the above choices.
Press the personalization button in order to select the displayed choice and to advance to the next option.
Headlamp Delay
Continue with the following steps in order to program the headlamp delay feature:

The DIC displays HEADLAMP DELAY: OFF, 10 SEC, 20 SEC, 30 SEC, 60 SEC, 120 SEC, or 180 SEC.
Press the select button in order to scroll through the above choices.
Press the personalization button in order to select the displayed choice and to advance to the next option.
Perimeter Lighting
Continue with the following steps in order to program the perimeter lighting feature:

The DIC displays PERIMETER LIGHTING: ON or OFF.
Press the select button in order to scroll through the above choices.
Press the personalization button in order to select the displayed choice and to advance to the next option.
Seat Position Recall
Continue with the following steps in order to program the memory position recall feature:

The DIC displays SEAT POSITION RECALL: ON REMOTE, AT KEY IN, or OFF.
Press the select button in order to scroll through the above choices.
Press the personalization button in order to select the displayed choice and to advance to the next option.
Easy Exit Seat
Continue with the following steps in order to program the exit position recall feature:

The DIC displays SEAT POSITION EXIT: ON or OFF.
Press the select button in order to scroll through the above choices.
Press the personalization button in order to select the displayed choice and to advance to the next option.
Curb View Assist
Continue with the following steps in order to program the Mirror Reverse Tilt feature:

The DIC displays CURB VIEW: PASSENGER, DRIVER, BOTH, or OFF.
Press the select button in order to scroll through the above choices.
When the vehicle is shifted into REVERSE and the Mirror Reverse Tilt feature is activated, any adjustments made to the preset position now becomes the new set position stored, this feature can be customized for each driver.
Press the personalization button in order to select the displayed choice and to advance to the next option.
Alarm Warning Type
Continue with the following steps in order to program the alarm warning feature:

The DIC displays ALARM WARNING: HORN, LAMPS, BOTH, or OFF.
Press the select button in order to scroll through the above choices.
Press the personalization button in order to select the displayed choice and to advance to the next option.
Display Language
Continue with the following steps in order to program the language displayed:

The DIC displays DISPLAY LANGUAGE: ENGLISH, FRENCH, or SPANISH.
Press the select button in order to scroll through the above choices.
Press the personalization button in order to select the displayed choice and to advance to the next option.
Display Units (ENG/MET)
Continue with the following steps in order to program the display units:

The DIC displays UNITS: ENGLISH or METRIC.
Press the select button in order to scroll through the above choices.
Press the personalization button in order to select the displayed choice and to advance to the next option.
Exit Programming
The following actions end the programming session:

The ignition is turned OFF.
The programming timer of 15 seconds expires.
The personalization button is pressed until the DIC scrolls through all of the personalization options.
Additional Information
For more information on the personalization features, refer to one of the following description and operations:

Refer to Power Door Locks Description and Operation in Doors for more information about the automatic door locks feature.
Refer to Interior Lighting Systems Description and Operation in Lighting Systems for more information about the following features:
Headlamp delay
Perimeter lighting
Refer to Keyless Entry System Description and Operation in Keyless Entry for more information about the remote activation verification feature.
Refer to Memory Seats Description and Operation in Seats for more information about memory seats.

99 silverado door lock
To enter programming mode you need to:

1.) Beginning with the ignition in OFF, pull back on the turn
signal/multifunction lever all the way toward you and hold it
while you perform the next step.

2.) Turn the key to ON and OFF twice. Then, with the key
in OFF, release the turn signal/multifunction lever. Once
you do this, you will hear the lock switch lock and unlock
and a ten second program timer will begin.

3.) You are now ready to program the automatic door locks.
Select one of the four programming options listed below.
Follow the instructions then wait for the ten second timer
to expire. The programmable auto door locks will now
operate in the selected mode. If you were unable to complete
the programming in the time allowed, repeat the procedure
beginning with step 1.
 

·
Registered
Joined
·
397 Posts
Discussion Starter #4
Available programming options:

All doors lock/Driver's door unlocks only::
Press the lock side of the power door lock switch on the
door panel once, and then the unlock side once.

All doors lock/All doors unlock::
Press the lock side of the power door lock switch on the
door panel once, and then the unlock side twice (this is
the factory setting)

All doors lock/None of the doors unlock::
Press the lock side of the power door lock switch in the
door panel once, and then the unlock side three times.

No doors lock/None of the doors unlock::
Press the lock side of the power door lock switch on
the door panel twice. This turns off the automatic door
lock feature.

'00 tahoes yukons silverados

Transmitter Programming
: 1.Start with the ignition OFF, hold down the power unlock button on the door panel. Turn ignition key ON,
: OFF, ON, OFF. Release power unlock button on the door panel. The locks will cycle once.
:
: 2.Hold down the keyless entry transmitter LOCK and UNLOCK buttons for 15 seconds. The locks will again
: cycle once.
:
: 3.Repeat step #2 for each additional keyless entry transmitter.
:
: 4.Turn the ignition on to exit the keyless entry transmitter programming mode. Programming is now
: complete.
 
1 - 4 of 4 Posts
Top